logo  
Product Range
bottom Shadow
 
 
   
 
Physics lab
[1]
Notice: Undefined variable: key in I:\wamp\www\vitco\product.php on line 120
2
Notice: Undefined variable: key in I:\wamp\www\vitco\product.php on line 137
[ Next»]
Search Results : 60 Product(s) Found.
 
Surface Tension Balance Searl's  [107.01 PH]
 
Approximately 275 mm length with cast metal bridge mounted on tripod stand adjustable for height & having a levelling knurled head screw fitted on one foot. The bridge has raised end pieces to which are screwed small metal blocks securing either end of a plated steel torsion wire. One block disc slotted to facilitate adjustment for torsion of the wire by means of screw passing through the end piece. At the centre of the wire, a small clamp is fitted carrying a light weight metal pointer with an adjustable counterpoise. From a notch near the tip of the pointer is suspended a small weight pan with a hook fitted to its underside, to hold either wire frame 80 x 25 mm or a metal clip carrying a glass microscope slide 75 x 25 x 1.5 mm. The tip of the pointer moves over a graduated vertical scale complete with set of weights 1 mgm to 1 gm.
 
Surface Tension Apparatus, Jaeger  [107.2 PH]
 
Convenient for determination of relative surface tensions, or after calibration with a liquid of known surface tension for determination of that of an unknown. Complete with tap funnel, having ground glass funnel to fit the 500 ml filter flask with side arm manometer, 500 ml beaker as bath, tube 150 x 30 mm with stirrer & three jets of different sizes. All glass parts made from corning glass.
 
Capillary Tubes Apparatus  [107.3 PH]
 
A 90 mm high metal frame having trough of 115 x 40 x 10 mm size. Frame having 6 holes fitted with corks. Trough which pan capillary tubes of different bore; 150 mm in length.
 
Kinetic Theory Model  [107.4 PH]
 

The apparatus consists of a clear perspex tube 380 mm long & 50 mm outer diameter provided with a light, freely sliding expanded polystyrene piston & a loose fitting metal cap. The tube is mounted by means of a bayonet type fitting in a metal cap, upon a polished wood motor housing 170 x 170 x 130 mm. A low voltage DC motor is contained in the housing & is coupled to crank driven agitator. The push rod of the agitator carries a light plastic piston which oscillates in the lower end of the tube. The apparatus is supplied complete with 3 mm diameter metal spheres & four cardboard loading discs.

Overall dimensions : 170 x 170 x 20 mm.
 
Smoke Cell  [107.5 PH]
 
For demonstrating Brownian motion. Designed for use with a microscope. A short cylindrical cell, closed by a cover glass, is held vertically in an opaque channel 90 x 90 x 30 mm. Illumination is by an integral filament bulb & cylindrical glass lens. The cell enables Brownian motion to be observed for at least 15 minutes after charging the cell with smoke. Fitted with 4 mm socket terminals for connection with 12V supply. With instructions.
 
Air Pump  [107.6 PH]
 
Single action Pump made of brass with oiled silk valves cylinder 200 x 32 mm. Plate 175 mm diameter with stopcock, & inlet screw fitted on teak wood polished base.
 
Ball & Ring Apparatus  [107.7 PH]
 
To demonstrate thermal expansion. Comprising a brass ball 25 mm diameter, a brass ring mounted on a rod with a wooden handle, a chain is provided to hold the ball with the ring. The ball passes through the ring when cold but does not after being heated.
 
Bar & Gauge  [107.8 PH]
 
A casted brass gauge with wooden handle, sliding fit over ends of bar & with hole 12.5 mm bore in both arms & a mild steel bar 110 x 12.5 mm with wooden handle.
 
Bar Breaking Apparatus  [107.9 PH]
 

To show force of contraction or expansion. A heavy cast iron base with 4 uprights, on one end of which is fitted a hand nut, the other drilled with holes to carry a cast iron rod of 75 x 6 mm size bearing against narrow flats.

Qverall Size : 330 x 60 x 60 mm with 12 cast iron breaking rods.
 
Expansion Apparatus  [107.10 PH]
 
Comprising two iron casted stand of 180 mm height joined by two chrome plated rods, with an expansion rod, length 380 mm, fixed on one stand & resting on a Friction pointer placed at the other. With graduated scale 0-90 with 3 expansion bars of Iron, Aluminium, & Brass.
 
Linear Expansion Apparatus  [107.11 PH]
 
The elongation of rod is measured by a micrometer screw. The brass tube is 500 x 25 mm C.P. With inlet & outlet tubes for steam & opening for thermometer reading to 1 x 110C. The binding posts are provided on the supports for connecting a belt, buzzer, or galvanometer for indicating the exact point of contact of the screw. Provided with three rods of Brass, Iron, & Aluminium.
 
Expansion Apparatus Gunther  [107.12 PH]
 

With two cast end pieces jointed by three nickel plated rods which carry two sliding V supports for a glass jacket with inlet & outlet tubes. One end piece fitted with spherometer reading to 0.005 mm & the other with contact screw. The glass jacket enclose both a brass & a copper rod each 500 x 6 mm fitted through corks, a half turn of the jacket changing the rod in contact with the spherometer. A thermometer can be attached to either side of the rods by rubber bands. Brass terminals are fitted to the apparatus so that an electrical circuit can be made through either rod to indicate the moment of contact of centre tube & spherometer.

Dimensions overall : 600 x 125 x 150 mm.

 
Expansion of Liquids Apparatus  [107.13 PH]
 
To show the differences in expansion of different liquids over the same temperature. Comprising five bulb tubes with plastic scales, mounted in a frame & supported in a G.I. sheet water trough 240 x 100 x 75 mm deep. The frame has clamps to secure it to the trough & two cross members having holes & upper tubules to locate the bulb tubes in bungs complete with 35 mm diameter bulbs & 150 mm scales etc.
 
Hypsometer Copper  [107.14 PH]
 

For determining the upper fixed point of thermometers & boiling points at barometer pressure other than atmospheric. Comprising an upper boiling vessel with a steam jacketed inner tube. A lid with a tubule is provided which holds the thermometer under test in a bung. A side outlet draining tube & a manometric tube mounted in a tubular with rubber bung.

Overall Size : 300 x 100 mm diameter.
 
Compound Rod  [107.15 PH]
 
For showing the difference in conductivity. Rod 300 x 18 mm half brass & half polished wood.
 
Compound Strips  [107.16 PH]
 
For demonstrating the differential expansion of two different metals. One each brass & iron plates 350 x 35 mm riveted together from end to end with wooden handle.
 
Thermostat Bimetallic  [107.18 PH]
 

Brass-invar control. For operation on gas supply, with adjustable screw valve & riffled connections for gas supply & burner.

Overall length : 140 mm
.
 
Edsers Apparatus  [107.19 PH]
 
A copper cylindrical vessel of 105 x 85 mm is fitted with 5 different rods of copper, brass, iron, aluminium, & zinc. All rods 150 x 3 mm & each having adjustable index mark at its base.
 
Hope's Apparatus  [107.20 PH]
 
For determining maximum density of water, made of G.I. sheet cylinder 50 mm diameter x 300 mm height mounted on a base having two tubulators for thermometers, with a gallery of 60 mm x 150 mm for placing mixture of ice & salt. The respective temperatures of water at the top & bottom of the inner cylindrical vessel are measured over a period as the water cools. Complete with bungs & thermometers.
 
Charle's Law Apparatus  [107.21 PH]
 
With a glass U tube with a bulb & tap at the upper end of one limb, other limb open. From the bottom of the U is an outlet tube which passes through a bung & terminates into a tap. The bulb has a capacity of 7 cm & the stem beneath is graduated 3 x 0.1 cm allowing for expansion over a range of 100C. The apparatus can be supported by a single clamp & only 20 cm of mercury is required.
 
Constant Volume Air Thermometer  [107.22 PH]
 
Consists of a polished teakwood stand approx. 750 mm high fitted with a wooden scale reading from 0 to 60 cm x 1 mm & supporting an adjustable mercury reservoir by a metal rod. A detachable air thermometer bulb about 70 mm diameter connected via three way stop cock to mercury tube with zero index fused inside its upper end. A metal vessel surrounding the bulb supported by detachable metal shelf mounted on insulated asbestos screen. Mounted on a teakwood stand with a deep tray which serves to catch any mercury spilled accidentally from the reservoir. Supplied complete with 1 meter of rubber pressure tubing 10 mm outer diameter & 5 mm bore for connecting the reservoir to the bulb.
 
Iron Flask for Freezing  [107.23 PH]
 
For demonstrating the expansion of water on freezing. A cast iron bottle 100 x 25 mm approx. which can be sealed by means of a well fitting screwed in iron plug.
 
Regnault's Hygrometer Simple  [107.24 PH]
 
For determining the dew point. Comprises a glass tube 150 x 25 mm with polished silver thimble closed bottom of the tube & the upper end by a rubber bung. The bung has two glass air tubes with right angled bends. One tube ending just below the bung, the other reaching nearly to the bottom of the thimble & a hole for thermometer which reads 10 to 50C x 0.5C.
 
Latent Heat of Steam Apparatus  [107.25 PH]
 
Comprises a thick brass calorimeter, a bung with steam inlet & outlet glass tubes, a felt cover, complete with 2 litres tin plate boiler with bung to take the steam tube which connects to the calorimeter.
 
Calorimeters Copper/ Aluminium  [107.26 PH]
 

One piece spinning with parallel sides & rolled rim, Available in both Copper & Aluminium.

Type Size (mm)
A 75 x 50 mm
B 100 x 75 mm
 
Calorimeter Set  [107.27 PH]
 
A complete set comprising the following : 1 copper calorimeter 75 x 50 mm 1 wooden outer box with felt lining 100 x 75 mm approx. 1 sliding wooden cover for outer box 1 copper stirrer with loop to fit inside the copper calorimeter 1 thermometer holder made of brass, removable
 
Calorimeter Set Copper  [107.28 PH]
 

Consisting of spun copper cylinder contained within a large 75 mm diameter x 100 mm aluminium outer vessel with 10 mm of insulating material between. Supplied with wooden cover for outer vessel with bung for mounting thermometer support clip.

Dimensions : 110 mm x 200 mm overall.
 
Joule's Calorimeter  [107.29 PH]
 
For determining the specific heat capacity of liquid by electrical method. Consisting of a nickel plated copper vessel 75 x 50 mm size with outer vessel of teak wood fitted with bakelite top with hole for thermometer. The terminals connected to a coil of wire (for current up to 3 amps.) are fitted, complete with stirrer & outer teakwood vessel.
 
Metal Block Calorimeters  [107.30 PH]
 
For experimental determination of the specific heat capacity of different metals. Cylindrical metal blocks of mass 1 kg; adjusted to accuracy of 2%. Each block drilled with two holes. A large central hole 12.5 mm diameter for a special immersion heater & a smaller hole, 7.5 mm diameter for a thermometer.
 
Cylinders Set Equal in Size  [107.31 PH]
 
A set of 6 metal cylinders 40 x 10 mm of copper, brass, iron, zinc, lead, & aluminium packed in card box. Each drilled for suspension.
 
Cylinders Set Equal in Mass  [107.32 PH]
 
A set of 6 metal cylinders of copper, brass, iron, zinc, lead, & aluminium of 100 gms each (10%) & each drilled for suspension.
[1]
Notice: Undefined variable: key in I:\wamp\www\vitco\product.php on line 221
2
Notice: Undefined variable: key in I:\wamp\www\vitco\product.php on line 241
[ Next»]
Home|Profile|Enquiry|Contact
© Copyright 2006. Vinay Trading Co. All Rights Reserved.